#include <Wire.h> #include <math.h> #define sampleFreq 33.30f // sample frequency in Hz #define twoKpDef (2.0f * 0.5f) // 2 * proportional gain #define twoKiDef (2.0f * 0.0f) // 2 * integral gain #define betaDef 0.1f //--------------------------------------------------------------------------------------------------- // Variable definitions volatile float twoKp = twoKpDef; // 2 * proportional gain (Kp) volatile float twoKi = twoKiDef; // 2 * integral gain (Ki) volatile float beta = betaDef; volatile float q0 = 1.0f, q1 = 0.0f, q2 = 0.0f, q3 = 0.0f; // quaternion of sensor frame relative to auxiliary frame volatile float integralFBx = 0.0f, integralFBy = 0.0f, integralFBz = 0.0f; // integral error terms scaled by Ki float phi; float theta; float psi; extern volatile float q0, q1, q2, q3; unsigned long time_ms = 0; void setup() { Serial.begin(9600); Wire.begin(); Wire.beginTransmission(0x68); Wire.write(0x6B); Wire.write(0); Wire.endTransmission(true); } void loop() { int x,y,z = 0; int t = 0; int a,b,c = 0; Wire.beginTransmission(0x68); Wire.write(0x3B); Wire.requestFrom(0x68, 14, true); Wire.endTransmission(true); x = Wire.read() << 8 | Wire.read(); y = Wire.read() << 8 | Wire.read(); z = Wire.read() << 8 | Wire.read(); t = Wire.read() << 8 | Wire.read(); a = Wire.read() << 8 | Wire.read(); b = Wire.read() << 8 | Wire.read(); c = Wire.read() << 8 | Wire.read(); double ax,ay,az; double gx,gy,gz; ax = x/16384.00f; ay = y/16384.00f; az = z/16384.00f; gx = a*3.1415926f/131.00f/180.00f; gy = b*3.1415926f/131.00f/180.00f; gz = c*3.1415926f/131.00f/180.00f; MadgwickAHRSupdateIMU(gx, gy, gz, ax, ay, az); time_ms = millis(); // Serial.print(time_ms); Serial.print(" "); Serial.print(q0); Serial.print(" "); Serial.print(q1); Serial.print(" "); Serial.print(q2); Serial.print(" "); Serial.print(q3); Serial.println(" "); // Serial.print(psi); // Serial.print(" "); // Serial.print(theta); // Serial.print(" "); // Serial.print(phi); // Serial.println(" "); // Serial.print(ax); // Serial.print(" "); // Serial.print(ay); // Serial.print(" "); // Serial.print(az); // Serial.println(" "); // Serial.print(gx); // Serial.print(" "); // Serial.print(gy); // Serial.print(" "); // Serial.print(gz); // Serial.println(" "); } void MahonyAHRSupdateIMU(float gx, float gy, float gz, float ax, float ay, float az) { float recipNorm; float halfvx, halfvy, halfvz; float halfex, halfey, halfez; float qa, qb, qc; // Compute feedback only if accelerometer measurement valid (avoids NaN in accelerometer normalisation) if(!((ax == 0.0f) && (ay == 0.0f) && (az == 0.0f))) { // Normalise accelerometer measurement recipNorm = invSqrt(ax * ax + ay * ay + az * az); ax *= recipNorm; ay *= recipNorm; az *= recipNorm; // Estimated direction of gravity and vector perpendicular to magnetic flux halfvx = q1 * q3 - q0 * q2; halfvy = q0 * q1 + q2 * q3; halfvz = q0 * q0 - 0.5f + q3 * q3; // Error is sum of cross product between estimated and measured direction of gravity halfex = (ay * halfvz - az * halfvy); halfey = (az * halfvx - ax * halfvz); halfez = (ax * halfvy - ay * halfvx); // Compute and apply integral feedback if enabled if(twoKi > 0.0f) { integralFBx += twoKi * halfex * (1.0f / sampleFreq); // integral error scaled by Ki integralFBy += twoKi * halfey * (1.0f / sampleFreq); integralFBz += twoKi * halfez * (1.0f / sampleFreq); gx += integralFBx; // apply integral feedback gy += integralFBy; gz += integralFBz; } else { integralFBx = 0.0f; // prevent integral windup integralFBy = 0.0f; integralFBz = 0.0f; } // Apply proportional feedback gx += twoKp * halfex; gy += twoKp * halfey; gz += twoKp * halfez; } // Integrate rate of change of quaternion gx *= (0.5f * (1.0f / sampleFreq)); // pre-multiply common factors gy *= (0.5f * (1.0f / sampleFreq)); gz *= (0.5f * (1.0f / sampleFreq)); qa = q0; qb = q1; qc = q2; q0 += (-qb * gx - qc * gy - q3 * gz); q1 += (qa * gx + qc * gz - q3 * gy); q2 += (qa * gy - qb * gz + q3 * gx); q3 += (qa * gz + qb * gy - qc * gx); // Normalise quaternion recipNorm = invSqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3); q0 *= recipNorm; q1 *= recipNorm; q2 *= recipNorm; q3 *= recipNorm; phi = atan(2*(q1*q2+q0*q3)/(-2*q2*q2+1-2*q3*q3)); theta = asin(2*(q1*q3-q0*q2)); psi = atan(2*(q1*q2+q0*q3)/(-2*q1*q1+1-2*q2*q2)); } void MadgwickAHRSupdateIMU(float gx, float gy, float gz, float ax, float ay, float az) { float recipNorm; float s0, s1, s2, s3; float qDot1, qDot2, qDot3, qDot4; float _2q0, _2q1, _2q2, _2q3, _4q0, _4q1, _4q2 ,_8q1, _8q2, q0q0, q1q1, q2q2, q3q3; // Rate of change of quaternion from gyroscope qDot1 = 0.5f * (-q1 * gx - q2 * gy - q3 * gz); qDot2 = 0.5f * (q0 * gx + q2 * gz - q3 * gy); qDot3 = 0.5f * (q0 * gy - q1 * gz + q3 * gx); qDot4 = 0.5f * (q0 * gz + q1 * gy - q2 * gx); // Compute feedback only if accelerometer measurement valid (avoids NaN in accelerometer normalisation) if(!((ax == 0.0f) && (ay == 0.0f) && (az == 0.0f))) { // Normalise accelerometer measurement recipNorm = invSqrt(ax * ax + ay * ay + az * az); ax *= recipNorm; ay *= recipNorm; az *= recipNorm; // Auxiliary variables to avoid repeated arithmetic _2q0 = 2.0f * q0; _2q1 = 2.0f * q1; _2q2 = 2.0f * q2; _2q3 = 2.0f * q3; _4q0 = 4.0f * q0; _4q1 = 4.0f * q1; _4q2 = 4.0f * q2; _8q1 = 8.0f * q1; _8q2 = 8.0f * q2; q0q0 = q0 * q0; q1q1 = q1 * q1; q2q2 = q2 * q2; q3q3 = q3 * q3; // Gradient decent algorithm corrective step s0 = _4q0 * q2q2 + _2q2 * ax + _4q0 * q1q1 - _2q1 * ay; s1 = _4q1 * q3q3 - _2q3 * ax + 4.0f * q0q0 * q1 - _2q0 * ay - _4q1 + _8q1 * q1q1 + _8q1 * q2q2 + _4q1 * az; s2 = 4.0f * q0q0 * q2 + _2q0 * ax + _4q2 * q3q3 - _2q3 * ay - _4q2 + _8q2 * q1q1 + _8q2 * q2q2 + _4q2 * az; s3 = 4.0f * q1q1 * q3 - _2q1 * ax + 4.0f * q2q2 * q3 - _2q2 * ay; recipNorm = invSqrt(s0 * s0 + s1 * s1 + s2 * s2 + s3 * s3); // normalise step magnitude s0 *= recipNorm; s1 *= recipNorm; s2 *= recipNorm; s3 *= recipNorm; // Apply feedback step qDot1 -= beta * s0; qDot2 -= beta * s1; qDot3 -= beta * s2; qDot4 -= beta * s3; } // Integrate rate of change of quaternion to yield quaternion q0 += qDot1 * (1.0f / sampleFreq); q1 += qDot2 * (1.0f / sampleFreq); q2 += qDot3 * (1.0f / sampleFreq); q3 += qDot4 * (1.0f / sampleFreq); // Normalise quaternion recipNorm = invSqrt(q0 * q0 + q1 * q1 + q2 * q2 + q3 * q3); q0 *= recipNorm; q1 *= recipNorm; q2 *= recipNorm; q3 *= recipNorm; } float invSqrt(float x) { float halfx = 0.5f * x; float y = x; long i = *(long*)&y; i = 0x5f3759df - (i>>1); y = *(float*)&i; y = y * (1.5f - (halfx * y * y)); return y; }
相关文章：