1-NET UX1000-实战-配置-Lync Server 2010-集成
1. 实验目的
FXS Quick Start 1.1
Configuring a call for the UX1000 FXS
Use the following step to configure a UX 1000 FXS Port.
Lync 分机----呼叫---FXS分机
8288------6001
FXS分机----呼叫--- Lync 分机
6001----8288
2. 登录-UX1000
用户名:admin
密 码:admin
3. 验证UX版本
Verifying the UX Versions
Prerequisite! Check your software level.
Verify that your UX1000 is loaded with firmware (boot partition) 2.1.6k and software p_w_picpath 2.0.0v108 or better. Older versions of
firmware/software will cause the FXS card to not function.
To begin the configuration, verify your Boot and Application versions.
3.1. 选择-Settings
3.2. 选择-System-Software Management-Boot Partition
3.3. 选择-System-Software Management-Application Partitions
Warning! Upgrade the UXSBA first.
If the UX application p_w_picpath requires an upgrade, always upgrade the UX Communication Service software (UXSBA) before upgrading
the UX application software. The firmware (boot) p_w_picpath can be upgraded either before or after the UX application software.
3.4. 验证-许可证
Verify Licensing
The system must have the FXS and DSP licenses to make calls. Depending upon the types of calls, the Transcoding license may also be necessary.
Unlimited---无限
SIP Registrations---注册普通的SIP话机
支持注册Skype
4. 验证-FXS卡/端口状态
Verify the FXS Card/Port State
Check to ensure that the FXS card and ports are functional by checking the System Tab | Overview Tab. The FXS Telco modules should show Activated, and the Service and Admin States should be UP.
Main Board:主板
FXS Not Activated and Up?
Did you upgrade the firmware and software?
5. 配置-UX1000 For FXS
Configuring the UX1000 for FXS
5.1. 增加-配置文件
Begin the configuration by adding a CAS Signaling Profile for FXS.
选择-Add FXS
选择-OK
首先得建立配置文件。
FXS Profile---S口的配置文件。
5.2. 增加-默认路由表
增加
Default Route Table
5.3. 增加-信令组
add a CAS Signaling Group
ISDN SG:---数字线路-信令组
SIP SG:-----IP-信令组---连接Lync Server 2010
CAS SG:----针对模拟线路，S口和O口
选择-Add CAS SG
Make sure to set the Channel Hunting to Own Number, otherwise the first free channel will answer every call (regardless of any other configuration settings).
参照:
Description:FXS Port 1
Channel Hunting:Own Number
Call Routing Table:Default Route Table
选择-OK
5.4. 分配号到-S口
Add an Assigned Channel and apply the desired phone number to the corresponding FXS port.
增加
Apply
The FXS-attached phone should now have dial-tone.
No dial-tone?
Are you certain your firmware and software are updated as noted at the beginning of these instructions?
5.5. 增加-一个FXS口呼叫的交换
Lync > FXS
FXS > PSTN
5.6. Lync 服务器
SIP
Add
Signaling Groups
5.7. 路由表
注意---更正---Lync > FXS
注意转换规则:
Lync > FXS
应用
应用
5.8. 测试
Lync---FXS
8288---6001
FXS---Lync
6001---8288
5.9.
6. 安装-jre-6u30-windows-i586-s.exe
7. 监控-通话
访问-NET UX1000
admin
admin
R是S口那边没挂断，正常挂断后不是这个样子。是绿色。
8. 安装-NET LX 2.8
NET LX 2.8---日志管理
9. UX1000-设置
10. 日志管理
10.1.打开-管理平台
10.2.选择-Syslog Server
10.3.选择-Start Listering
10.4.Lync分机---呼叫---FXS口
8288---》---6001
10.5.接听
10.6.选择-Stop Listering
10.7.选择-分析
10.8.
11. Lync分机---呼叫---FXS口分机
11.1.SIP
SIP Server Tables
填写:
Lync Server 2010-服务器
192.168.1.82 5068
SIP Options
11.2.CAS
新建-FXS---分机配置文件
FXS Profile
11.3.Signaling Groups
信令组
CAS SG CAS信令组
写入FXS口---分机号
SIP SG SIP信令组
写入 SIP服务器
FX0---也需要建信令组.需实战
E1----也需要建信令组.需实战
11.4.Transformation
转换规则
11.5.Call Routing Table
转载于:https://blog.51cto.com/dynamic/767106