触摸屏不适用于 Debian 9.13 和 HX 控制器

【问题标题】：Touchscreen doest work with Debian 9.13 and HX controller触摸屏不适用于 Debian 9.13 和 HX 控制器
【发布时间】：2021-07-05 10:01:17
【问题描述】：

带有触摸屏框架的夏普显示器通过 USB 和 HDMI 连接到 PC。 Debian 9.13 (4.9.0-16-amd64)

SO 启动时，触摸屏在我按下时不起作用，但如果我拔下并插入 USB，它就会起作用。

这是我的配置：

添加到 /etc/X11/xorg.conf.d/53-touchscreen.conf 以捕获所有事件并忽略 HX 触控设备笔

Section "InputClass"
    Identifier "HX Touch catchall"
    MatchProduct "HX Touch Device"
    MatchDevicePath "/dev/input/event*"
    Driver "libinput"
EndSection

Section "InputClass"
    Identifier "HX Touch Pen deactive"
    MatchProduct "HX Touch Device Pen"
    MatchDevicePath "/dev/input/event*"
    MatchVendor "HX"
    Driver "void"
    Option "Ignore"
EndSection

开机信息

x输入

⎡ Virtual core pointer                          id=2    [master pointer  (3)]
⎜   ↳ Virtual core XTEST pointer                id=4    [slave  pointer  (2)]
⎜   ↳ HX Touch Device                           id=9    [slave  pointer  (2)]
⎣ Virtual core keyboard                         id=3    [master keyboard (2)]
    ↳ Virtual core XTEST keyboard               id=5    [slave  keyboard (3)]
    ↳ Video Bus                                 id=6    [slave  keyboard (3)]
    ↳ Power Button                              id=7    [slave  keyboard (3)]

xinput --list-props 9

Device 'HX Touch Device':
        Device Enabled (133):   1
        Coordinate Transformation Matrix (135): 1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Calibration Matrix (272):      1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Calibration Matrix Default (273):      1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Send Events Modes Available (255):     1, 0
        libinput Send Events Mode Enabled (256):        0, 0
        libinput Send Events Mode Enabled Default (257):        0, 0
        Device Node (258):      "/dev/input/event4"
        Device Product ID (259):        1245, 40593

dmesg

[    1.873563] usb 1-2: not running at top speed; connect to a high speed hub
[    1.874157] usb 1-2: New USB device found, idVendor=04dd, idProduct=9e91
[    1.874160] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.874162] usb 1-2: Product: Touch Device
[    1.874164] usb 1-2: Manufacturer: HX
[    2.643435] input: HX Touch Device Pen as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0002/input/input3
[    2.644115] input: HX Touch Device as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0002/input/input4
[    2.649479] hid-multitouch 0003:04DD:9E91.0002: input,hiddev0,hidraw1: USB HID v2.00 Mouse [HX Touch Device] on usb-0000:00:15.0-2/input0

udevadm info --query=all --attribute-walk /dev/input/event4

  looking at device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0002/input/input4/event4':
    KERNEL=="event4"
    SUBSYSTEM=="input"
    DRIVER==""

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0002/input/input4':
    KERNELS=="input4"
    SUBSYSTEMS=="input"
    DRIVERS==""
    ATTRS{name}=="HX Touch Device"
    ATTRS{phys}=="usb-0000:00:15.0-2/input0"
    ATTRS{properties}=="2"
    ATTRS{uniq}==""

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0002':
    KERNELS=="0003:04DD:9E91.0002"
    SUBSYSTEMS=="hid"
    DRIVERS=="hid-multitouch"
    ATTRS{country}=="00"
    ATTRS{quirks}=="4112"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0':
    KERNELS=="1-2:1.0"
    SUBSYSTEMS=="usb"
    DRIVERS=="usbhid"
    ATTRS{authorized}=="1"
    ATTRS{bAlternateSetting}==" 0"
    ATTRS{bInterfaceClass}=="03"
    ATTRS{bInterfaceNumber}=="00"
    ATTRS{bInterfaceProtocol}=="00"
    ATTRS{bInterfaceSubClass}=="00"
    ATTRS{bNumEndpoints}=="02"
    ATTRS{interface}=="Touch Device"
    ATTRS{supports_autosuspend}=="1"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2':
    KERNELS=="1-2"
    SUBSYSTEMS=="usb"
    DRIVERS=="usb"
    ATTRS{authorized}=="1"
    ATTRS{avoid_reset_quirk}=="0"
    ATTRS{bConfigurationValue}=="1"
    ATTRS{bDeviceClass}=="00"
    ATTRS{bDeviceProtocol}=="00"
    ATTRS{bDeviceSubClass}=="00"
    ATTRS{bMaxPacketSize0}=="64"
    ATTRS{bMaxPower}=="2mA"
    ATTRS{bNumConfigurations}=="1"
    ATTRS{bNumInterfaces}==" 1"
    ATTRS{bcdDevice}=="5001"
    ATTRS{bmAttributes}=="a0"
    ATTRS{busnum}=="1"
    ATTRS{configuration}==""
    ATTRS{devnum}=="3"
    ATTRS{devpath}=="2"
    ATTRS{idProduct}=="9e91"
    ATTRS{idVendor}=="04dd"
    ATTRS{ltm_capable}=="no"
    ATTRS{manufacturer}=="HX"
    ATTRS{maxchild}=="0"
    ATTRS{product}=="Touch Device"
    ATTRS{quirks}=="0x0"
    ATTRS{removable}=="removable"
    ATTRS{speed}=="12"
    ATTRS{urbnum}=="17"
    ATTRS{version}==" 2.00"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1':
    KERNELS=="usb1"
    SUBSYSTEMS=="usb"
    DRIVERS=="usb"
    ATTRS{authorized}=="1"
    ATTRS{authorized_default}=="1"
    ATTRS{avoid_reset_quirk}=="0"
    ATTRS{bConfigurationValue}=="1"
    ATTRS{bDeviceClass}=="09"
    ATTRS{bDeviceProtocol}=="01"
    ATTRS{bDeviceSubClass}=="00"
    ATTRS{bMaxPacketSize0}=="64"
    ATTRS{bMaxPower}=="0mA"
    ATTRS{bNumConfigurations}=="1"
    ATTRS{bNumInterfaces}==" 1"
    ATTRS{bcdDevice}=="0409"
    ATTRS{bmAttributes}=="e0"
    ATTRS{busnum}=="1"
    ATTRS{configuration}==""
    ATTRS{devnum}=="1"
    ATTRS{devpath}=="0"
    ATTRS{idProduct}=="0002"
    ATTRS{idVendor}=="1d6b"
    ATTRS{interface_authorized_default}=="1"
    ATTRS{ltm_capable}=="no"
    ATTRS{manufacturer}=="Linux 4.9.0-16-amd64 xhci-hcd"
    ATTRS{maxchild}=="8"
    ATTRS{product}=="xHCI Host Controller"
    ATTRS{quirks}=="0x0"
    ATTRS{removable}=="unknown"
    ATTRS{serial}=="0000:00:15.0"
    ATTRS{speed}=="480"
    ATTRS{urbnum}=="44"
    ATTRS{version}==" 2.00"

  looking at parent device '/devices/pci0000:00/0000:00:15.0':
    KERNELS=="0000:00:15.0"
    SUBSYSTEMS=="pci"
    DRIVERS=="xhci_hcd"
    ATTRS{broken_parity_status}=="0"
    ATTRS{class}=="0x0c0330"
    ATTRS{consistent_dma_mask_bits}=="64"
    ATTRS{d3cold_allowed}=="1"
    ATTRS{device}=="0x5aa8"
    ATTRS{dma_mask_bits}=="64"
    ATTRS{driver_override}=="(null)"
    ATTRS{enable}=="1"
    ATTRS{irq}=="365"
    ATTRS{local_cpulist}=="0-3"
    ATTRS{local_cpus}=="f"
    ATTRS{msi_bus}=="1"
    ATTRS{numa_node}=="-1"
    ATTRS{subsystem_device}=="0x7270"
    ATTRS{subsystem_vendor}=="0x8086"
    ATTRS{vendor}=="0x8086"

  looking at parent device '/devices/pci0000:00':
    KERNELS=="pci0000:00"
    SUBSYSTEMS==""
    DRIVERS==""

重新连接 USB 电缆和触摸屏开始工作后的信息

dmesg

[  619.750184] usb 1-2: USB disconnect, device number 3
[  630.026900] usb 1-2: new full-speed USB device number 4 using xhci_hcd
[  630.167200] usb 1-2: not running at top speed; connect to a high speed hub
[  630.167827] usb 1-2: New USB device found, idVendor=04dd, idProduct=9e91
[  630.167830] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  630.167833] usb 1-2: Product: Touch Device
[  630.167845] usb 1-2: Manufacturer: HX
[  630.185722] input: HX Touch Device Pen as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0003/input/input11
[  630.186097] input: HX Touch Device as /devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0003/input/input12
[  630.186467] hid-multitouch 0003:04DD:9E91.0003: input,hiddev0,hidraw1: USB HID v2.00 Mouse [HX Touch Device] on usb-0000:00:15.0-2/input0

xinput --list-props 9

Device 'HX Touch Device':
        Device Enabled (133):   1
        Coordinate Transformation Matrix (135): 1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Calibration Matrix (272):      1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Calibration Matrix Default (273):      1.000000, 0.000000, 0.000000, 0.000000, 1.000000, 0.000000, 0.000000, 0.000000, 1.000000
        libinput Send Events Modes Available (255):     1, 0
        libinput Send Events Mode Enabled (256):        0, 0
        libinput Send Events Mode Enabled Default (257):        0, 0
        Device Node (258):      "/dev/input/event4"
        Device Product ID (259):        1245, 40593

udevadm info --query=all --attribute-walk /dev/input/event4

  looking at device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0003/input/input12/event4':
    KERNEL=="event4"
    SUBSYSTEM=="input"
    DRIVER==""

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0003/input/input12':
    KERNELS=="input12"
    SUBSYSTEMS=="input"
    DRIVERS==""
    ATTRS{name}=="HX Touch Device"
    ATTRS{phys}=="usb-0000:00:15.0-2/input0"
    ATTRS{properties}=="2"
    ATTRS{uniq}==""

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0/0003:04DD:9E91.0003':
    KERNELS=="0003:04DD:9E91.0003"
    SUBSYSTEMS=="hid"
    DRIVERS=="hid-multitouch"
    ATTRS{country}=="00"
    ATTRS{quirks}=="4112"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2/1-2:1.0':
    KERNELS=="1-2:1.0"
    SUBSYSTEMS=="usb"
    DRIVERS=="usbhid"
    ATTRS{authorized}=="1"
    ATTRS{bAlternateSetting}==" 0"
    ATTRS{bInterfaceClass}=="03"
    ATTRS{bInterfaceNumber}=="00"
    ATTRS{bInterfaceProtocol}=="00"
    ATTRS{bInterfaceSubClass}=="00"
    ATTRS{bNumEndpoints}=="02"
    ATTRS{interface}=="Touch Device"
    ATTRS{supports_autosuspend}=="1"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1/1-2':
    KERNELS=="1-2"
    SUBSYSTEMS=="usb"
    DRIVERS=="usb"
    ATTRS{authorized}=="1"
    ATTRS{avoid_reset_quirk}=="0"
    ATTRS{bConfigurationValue}=="1"
    ATTRS{bDeviceClass}=="00"
    ATTRS{bDeviceProtocol}=="00"
    ATTRS{bDeviceSubClass}=="00"
    ATTRS{bMaxPacketSize0}=="64"
    ATTRS{bMaxPower}=="2mA"
    ATTRS{bNumConfigurations}=="1"
    ATTRS{bNumInterfaces}==" 1"
    ATTRS{bcdDevice}=="5001"
    ATTRS{bmAttributes}=="a0"
    ATTRS{busnum}=="1"
    ATTRS{configuration}==""
    ATTRS{devnum}=="4"
    ATTRS{devpath}=="2"
    ATTRS{idProduct}=="9e91"
    ATTRS{idVendor}=="04dd"
    ATTRS{ltm_capable}=="no"
    ATTRS{manufacturer}=="HX"
    ATTRS{maxchild}=="0"
    ATTRS{product}=="Touch Device"
    ATTRS{quirks}=="0x0"
    ATTRS{removable}=="removable"
    ATTRS{speed}=="12"
    ATTRS{urbnum}=="1621"
    ATTRS{version}==" 2.00"

  looking at parent device '/devices/pci0000:00/0000:00:15.0/usb1':
    KERNELS=="usb1"
    SUBSYSTEMS=="usb"
    DRIVERS=="usb"
    ATTRS{authorized}=="1"
    ATTRS{authorized_default}=="1"
    ATTRS{avoid_reset_quirk}=="0"
    ATTRS{bConfigurationValue}=="1"
    ATTRS{bDeviceClass}=="09"
    ATTRS{bDeviceProtocol}=="01"
    ATTRS{bDeviceSubClass}=="00"
    ATTRS{bMaxPacketSize0}=="64"
    ATTRS{bMaxPower}=="0mA"
    ATTRS{bNumConfigurations}=="1"
    ATTRS{bNumInterfaces}==" 1"
    ATTRS{bcdDevice}=="0409"
    ATTRS{bmAttributes}=="e0"
    ATTRS{busnum}=="1"
    ATTRS{configuration}==""
    ATTRS{devnum}=="1"
    ATTRS{devpath}=="0"
    ATTRS{idProduct}=="0002"
    ATTRS{idVendor}=="1d6b"
    ATTRS{interface_authorized_default}=="1"
    ATTRS{ltm_capable}=="no"
    ATTRS{manufacturer}=="Linux 4.9.0-16-amd64 xhci-hcd"
    ATTRS{maxchild}=="8"
    ATTRS{product}=="xHCI Host Controller"
    ATTRS{quirks}=="0x0"
    ATTRS{removable}=="unknown"
    ATTRS{serial}=="0000:00:15.0"
    ATTRS{speed}=="480"
    ATTRS{urbnum}=="66"
    ATTRS{version}==" 2.00"

  looking at parent device '/devices/pci0000:00/0000:00:15.0':
    KERNELS=="0000:00:15.0"
    SUBSYSTEMS=="pci"
    DRIVERS=="xhci_hcd"
    ATTRS{broken_parity_status}=="0"
    ATTRS{class}=="0x0c0330"
    ATTRS{consistent_dma_mask_bits}=="64"
    ATTRS{d3cold_allowed}=="1"
    ATTRS{device}=="0x5aa8"
    ATTRS{dma_mask_bits}=="64"
    ATTRS{driver_override}=="(null)"
    ATTRS{enable}=="1"
    ATTRS{irq}=="366"
    ATTRS{local_cpulist}=="0-3"
    ATTRS{local_cpus}=="f"
    ATTRS{msi_bus}=="1"
    ATTRS{numa_node}=="-1"
    ATTRS{subsystem_device}=="0x7270"
    ATTRS{subsystem_vendor}=="0x8086"
    ATTRS{vendor}=="0x8086"

  looking at parent device '/devices/pci0000:00':
    KERNELS=="pci0000:00"
    SUBSYSTEMS==""
    DRIVERS==""

我不知道为什么在启动时不工作，但是当我拔掉并插入 USB 电缆时是的。

【问题讨论】：

  • 是否可以修改 KERNELS 值？
  • 我已尝试从控制台重置 USB，但也没有用。从反向移植更新内核也不起作用
  • 在 Ubuntu 20.04 上不起作用
  • 在 Fedora 34 上相同 5.15.12-100.fc34 unix.stackexchange.com/questions/684954/…

标签： linux debian usb touchscreen


【解决方案1】：

首先，我还没有找到问题的解决方案。
但我有一个可能对你有帮助的解决方法。

您可以使用modprobe -r hid_multitouch卸载hid_multitouch，它将开始工作。

但是：因为我们卸载了hid_multitouch 模块，触摸将被识别为鼠标指针设备。您可以查看xinput --list 输出以获取更多信息。

所以你所做的所有事件都是正常的鼠标事件。
这会带来其他问题（例如没有捏缩放）。

用modprobe hid_multitouch 重新加载hid_multitouch 不起作用，或者换句话说，没有按预期打开触摸功能。它不会做任何事情......

您可以在
https://unix.stackexchange.com/questions/684954/touchscreen-device-doesnt-work-after-boot-but-does-on-replug

上找到我的观察结果

【讨论】：

    猜你喜欢
    • 2014-09-02
    • 1970-01-01
    • 2017-08-31
    • 1970-01-01
    • 1970-01-01
    • 1970-01-01
    • 1970-01-01
    • 2010-10-13
    • 1970-01-01
    相关资源
    最近更新 更多
    热门标签
    Java Python linux javascript Mysql C# Docker 算法 前端 SpringBoot Redis Vue spring 设计模式 .net core .net kubernetes c++ 数据库 数据结构 大数据 js 机器学习 微服务 Android Go 程序员 面试 JVM ASP.net core 云原生 人工智能 后端 PHP git CSS golang k8s Nginx Django mybatis 深度学习 多线程 React 架构 devops 爬虫 云计算 Spring Boot LeetCode